SriHome 4MP IP Solar Power WiFi Camera DH006 HD Wireless Security HD CCTV Waterproof Cam utdoor Surveillance Security Cameras

About this item

1:4MP Solar Wireless Battery Outdoor Waterproof Camera,Waterproof：IP65
2:Battery: Support four 18650 batteries(Two batteries as standard，4000mA)
3:Low power consumption: Ultra-low power consumption, long standby time
4:Pan Tilt: Pan:350°, Tilt: 90°
5:Audio: Two-way audio, built-in microphone and speaker, support monitoring and intercom
6:Lens: 4mm lens, viewing angle 110°, support 3x electronic zoom
7:Light: Infrared light and warm light, full-color night vision
8:TF card:Support 128G TF Card,support mobile video playback
9:Privacy Protection: The system defaults the first user as the administrator, and other users must be authorized by the administrator before accessing the camera
10.APP:Support Android,IOS

Image sensor

Sensor：CMOS sensor 1/3"
Pixel：2560*1440
Minimum illumination：0.1LUX/F1.2

Len

Lens parameters：Focal length: 4mm,viewing angle 110°

Battery

Specification：2*2000mA Battery Pack (built-in)
Standby time：4000mA batteries standby for about 6 months
Standby current：Less than 1mA
Wake up time：About 5800 times (4000mA 18650 batteries)
charging input：Type C, 5V
Charging input：Solar panel, power adapter,power bank (DC 5V )
Battery insulating sheet：Before use,it is necessary to remove the insulating sheet

Video

Resolution：(2560*1440)1440P, (640*360)360P
Compression format：H.264
Frame frequency：20 fps
Exposure：Auto exposure white balance
WDR：Digital WDR
IR-Cut：No color cast during the day, good night vision
Zoom：App supports 3x digital zoom

Network

Wireless：2.4G (11bng) mixed
Distribution mode：QR code distribution network
Online users: Number of simultaneous online viewers: 5 people are supported at the same time.

PTZ

Support: Pan:350°, Tilt: 90°

How to setup microSD card record settings

SD card installation video：https://www.youtube.com/embed/nbpofPlUV2k

Note: Cameras maximum support 128 GB SD card.

1). Remove power cable before inserting the microSD card to the camera.

2). MicroSD card format and record setting

Log in “SriHome” App and follow the steps:Settings -> Record Setting .

There are 2 types of recordings：

24/7 recording: 24/7 recording refers to the continuous recording of the camera which is about every 10 minutes as a node continuous recording.

Alarm recording: The camera captures footage only when the motion detection alarm is activated.

The system does not detect SD Card.

Followings are a few possible reasons why this may be occurring:

1. Please power off camera before inserting SD card into camera.

2. The SD card read&write speed not good, please use a SD card with class 10 or above class 10.

4. The SD card is broken.

3. The SD card has not been formatted properly.

5. The SD card slot is faulty.

SD card video playback view:

Note:Both 24/7 recording and Alarm recording cannot be opened at the same time ,only one of them can be opened.

The system does not detect an SD Card

1. Please power off camera before inserting SD card into camera.

2. The SD card read&write speed not good, please use a SD card with class 10 or above class 10.

3. The SD card is broken.

4. The SD card has not been formatted properly. please format sd www.sricam.com/srihome/download

5. The SD card slot is malfunctioning.

Camera’s Wi-Fi is unstable and often offline

1. Check whether antenna is tightened.

2. Set maximum transmission power:In some wireless routers, the transmission power can be reduced,which reduces the performance

of the wireless network. Make sure your wireless router has the maximum transmit power set.

3. WiFi channels: check if WiFi channels are busy, possibly reconfigure to “Automatic”.

4. The camera IP address conflicts with other devices, needing to set camera IP address to be a

fixed one.

5. Change the name of the wireless network (SSID): If there are different wireless networks with the same name (SSID) in your

environment-perhaps because a neighbor uses the same wireless router,a wireless repeater has the same name as the router – WLAN

devices could try to automatically connect to the wrong wireless network ,Therefore, set up a unique wireless network name in your

wireless router or repeater.

6. To check Wi-Fi signal, in normally, it should be more than 3 bars.

(The distance between the camera and wifi router being too far might cause wifi signal to be less than 3 bars ).

Can’t connect WiFi

If you fail to setting WiFi for ip camera, please make sure your router：

1. All IP Cameras support 2.4G HZ WIFI，only some IP cameras don’t support 5GHZ Wi-Fi.

2. NO MAC filter enabled on your router. Or you need to disable MAC filter temporarily before successfully configuring camera.

3. Router’s DHCP is enabled, after setting up and setting a fixed ip address for IP camera, you can disable DHCP again.

4. The WiFi Encryption is WPA/WPA2-PSK, either AES or TKIP encryption is OK if you are not using WPA/WPA2.

There is possible using WEP. It is recommended to use WPA/WPA2 now because WEP is quite old technology and not safe nowadays.

5. WiFi Channel needs to set as AUTO in order to avoid busy channels.

Inconsistent signal, it could be due to:

1) Too many devices sharing the same internet network. Please try to disconnect other devices.

2) The IP camera is too far from the router if using WIFI connection.

• Other quality and setup issue, please reset camera to factory default.

How to restore the camera to factory settings?

Step 1: Power on the IP Camera and wait for about 30 seconds

Step 2: Keep pressing the RESET button for about 15 seconds then release.

Then camera successfully restore to factory settings (password default : 888888).

About us

Srihome was founded in 2013 and specializes in manufacturing intelligent security network cameras. So far, our monthly production exceeds 100000 units, and our customers are located in more than 80 countries including the United States, Canada, Italy, Russia, Brazil, France, the United Kingdom, South Korea, Japan, and more.